AGMA 2000-A88 PDF

ANSI/AGMA A Gear Classification and Inspection Handbook – Tolerances and Measuring Methods for Unassembled Spur and Helical Gears ( including. 2 Aug Credit line should read Extractedfrom AGMA Standard A88, Gear Classificationandhspection Handbook,Tolerances Measuring and. Please Consensus on this matter Customer Engineering Drawing Gear Tab Block Gear Data Specifies AGMA Q8 # Teeth Diametral Pitch.

Author: Bratilar Akinotilar
Country: Togo
Language: English (Spanish)
Genre: Education
Published (Last): 21 May 2012
Pages: 193
PDF File Size: 19.99 Mb
ePub File Size: 6.17 Mb
ISBN: 846-7-13598-717-1
Downloads: 59844
Price: Free* [*Free Regsitration Required]
Uploader: Akinoshakar

Are you an Engineering professional? These changes, determined after publication and Errata A, have been made in this printing, as shown below: My suggestion is that you make your frustrations known to AGMA by sending them an email outlining your frustrations.

If you insist on the dimensions over pins then you have to measure all the teeth. Appendix material provides guidance on specifying levels and information on additional methods of gear inspection.

Close this window and log in. As the voice of the U.

AGMA ANSI/AGMA 2000-A88 – Gear Classification and Inspection Handbook:…

We have no document history for this standard. It is mainly based on it but with some differences.

Therefore, if the gear has teeth for example, you need to do 50 tests for each gear to get the TTCE and the TCE which is a time consuming process. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Standards Subsctiption may be the perfect solution. Thank you for helping keep Eng-Tips Forums free from inappropriate posts. The standards were developed to allow for use of nice linear equations as opposed to comply with a particular manufacturing process or part application.


Item Detail – ANSI/AGMA A88 (Note: standard was withdrawn & replaced)

Additional corrections were also discovered after publication and Errata A: In my opinion, the best method is to explicity state on your drawings what you want measured and state the explicit tolerance. Trapp Klingelnberg Soehne R. AGMA only requires total composite and tooth to tooth composite to be measured. Ansi Agma a Please first log in with a verified email before subscribing to alerts. Does your customer’s documentation specify the quality class in accordance with AGMA A88, or are 200-a88 just assuming that?

You may delete a document from your Alert Profile at any time. You should tell them your concerns and experiences with the new and -2 standards.

AGMA 2000-A88.pdf

Thank you for visiting our website and your interest in our free products and services. If you have many parts and you can afford a master pinion, you are probably better off using the tce check method.


Consultant Chairman Subcommittee Classification System: That is why my OP was asking the question? We Need Your Support.

Further to this, it may be easier to meet Q10 on tooth to tooth error than 0200-a88, or on Lead then on Profile. Porter Illinois Tool Works V.

AGMA Apdf – Documents

By joining you are opting in to receive e-mail. The AGMA only deals with the variations on the base gear dimensions but not the base dimensions. Inthe same thing can be said for the profile and helix callouts where once may meet a A9 quality class while the other is better at an A7. Itprovides information on manufacturing practices as well as gear measuring methods and practices. Rychlinski 2000a-88 Foote P. Correlates gear quality levels with gear tooth tolerances. Promoting, selling, recruiting, coursework and thesis posting is forbidden.

For certain if you need to control a special element of the standard, it should be specified. Such issues are the result of project complexity, size, uniqueness and regulation, as well as the need for virtual team collaboration.