SIMOREG K 6RA22 PDF

SIMOREG K 6RA22; converter with mircroprocessor from 12kW to kW in circulating-current-free inverse-parallel (B6)A(B6)C connection. Entry. Associated . SIEMENS. SIMOREG K. 6RA22 converter with microprocessor in a fully controlled three-phase bridge circuit connection B6C. *IIII. III. SIEMENS. SIMOREG. I am looking for Simoreg K 6RA22 manual. I already seached in the siemens website but unable to get the manual. Can anyone send me the.

Author: Meztibar Kazraramar
Country: Angola
Language: English (Spanish)
Genre: Marketing
Published (Last): 18 October 2010
Pages: 19
PDF File Size: 3.25 Mb
ePub File Size: 13.47 Mb
ISBN: 273-5-66556-123-3
Downloads: 92710
Price: Free* [*Free Regsitration Required]
Uploader: Kajar

Even outside the cabinet, the shields may be connected in several places.

The F 33 Minireg can also be mounted on a vertical surface by means of four spacers, e. Information about the Machine More information. LD Physics Leaflets P4.

SIMOREG K 6RA22 Analog Chassis Converters. Catalog DA

A partition plate should be used if necessary. The feedback can be adapted by soldering-in other components. The shields of digital signal cables should have largearea good electrical grounding at each end source and destination.

Information about the Machine. HERZ-Thermal Actuators Data SheetIssue Dimensions in mm 1 00 1 01 1 18 1 80 1 81 1 80 1 81 1 00 1 00 1 11 1 10 1 23 1 If the system is to comply with the A1 degree of radio interference suppression according to ENRI suppression filters must be installed in addition to commutating reactors.

Limit monitor has responded. 6rs22

The choice of solution, therefore, also depends on economic factors. By means of the auto-reverse stage, the trigger pulses are fed, according to the required torque direction, to the thyristors associated with the required current direction via pulse amplifiers and the transformer section.

TOP Related Articles  SIEMENS TC35 PDF

La Paz Brazil Siemens Ltda. Interference sources are usually devices of power electronics with a high current consumption. Rules 11 to 15 are necessary to meet the emitted interference standards. With this measuring method, the zero diode current of the thyristor circuit is also sensed.

Is that on the link the one you are looking for? Examples of interference sinks are programmable controllers, encoders and sensors. The following conditions apply: When the V supply voltage is switched on, 0 V then appears at the output and not the value in the nonvolatile memory. The input signals of channels I and II are available at two decoupled outputs.

Whether the motorized potentiometer is ramping-up or ramping-down is insignificant. The cabinet door should be connected to the cabinet via ground straps at top, middle and bottom with as short a path a possible.

The supply current is equal to the DC multiplied by d The commutating reactor in the armature circuit is designed for the rated motor current in the armature. The following setpoints act on the speed controller: Interference sinks are, in particular, control units and sensors including their evaluation circuitry.

SIMOREG K 6RA22 Analog Chassis Converters. Catalog DA – PDF

The commutating reactors are dimensioned for the rated motor current in the armature or field circuit. The unit can also be mounted directly on a vertical surface, e. Environmental aspects were an important criteria in selecting the supplied components.

The supplementary board to be powered is mounted, in turn, on the power supply board with spacer bolts. An external reference voltage can be applied to terminal 19 for special applications, thus allowing the maximum output voltage to be varied.

Maximum 30W output power Silvertel V1.

TOP Related Articles  HOLMES RAHE STRESS TEST PDF

SIMOREG K 6RA22 PDF

DCS Series 1 kw, 1. No part of this document may be stored in a retrieval system, or transmitted, in.

In expectation on your kindness we thank you simoreg k 6ra22 today. The setpoint which, for example, corresponds to the rated field, can be set with potentiometer R Safety More than safety. In general, shields may be connected to the cabinet housing ground at several points. Wiring should therefore not be placed in free space in the cabinet but, where possible, routed closely along the cabinet housing or installation plates. It will also show the user how to More information.

The direction of rotation can be evaluated by connecting two channels, electrically offset by 90, so that the DC output voltage is also available with sign. A minimum clearance 20 cm is desirable. Features 76 2 Load regulated multi-protocol decoder. The values have been adopted from a previous publication: Rules for electromagnetically compatible installation Rule 1 All metal parts of the cabinet must be joined to each other with good electrical contact not paintwork on paint-work!

To use this website, you must agree to our Privacy Policyincluding cookie policy.

As early as the development phase, the possible impact of future products and systems on the environment is taken into consideration. For winder operation, the winding roll speed must be reduced according to the increasing roll diameter; for unwinding operation, in contrast, the speed must be increased in accordance with the descreasing roll diameter.